IGNITER BREAKOUT BOARD & QUICKPLUG HARNESS

Breakout Boards are a convenient, re-usable solution for wiring multiple igniters to a single cue.

If you are using Clip-On Igniters, you can plug up to two igniters into the breakout board.

If you are using Fuse-Tube Igniters, you can plug up to five igniters into the breakout board, or use multiple breakout boards together for a maximum of 10 Fuse-Tube Igniters per cue.

Includes:

• 1 x Breakout Board
• 1 x Quickplug Harness

more images

×

$8.99

• Qty :
• Add to Cart
• Add to Cart

QUICKPLUG 6-CUE TESTER

You can use up to three Quickplug 6-Cue Testers with the IGNITE i18 module or up to six with the IGNITE i36 module, making it a must-have tool for pyrotechnic enthusiasts.

This compact device features six blue LEDs on the front panel, labeled from 1 to 6. When plugged into an IGNITE module and cues are fired, the corresponding LED lights up, providing instant visual confirmation. Even when no cues are firing, the LED pulses, indicating the module is actively checking cue connections.

Using the Quickplug 6-Cue Testers, you can easily verify cue activation and ensure a seamless pyrotechnic display. Simplify your setup and gain peace of mind with this reliable cue-testing solution.

view images

×

$8.99

• Qty :
• Add to Cart
• Add to Cart

ARMORED CASE EXTERNAL ANTENNA CABLE

Antenna Cable used to relocate the antenna connector to outside an armored case such as the Pelican 1050 micro case (sold separately). To drill a hole in the case, use a 1/4" drill bit.

Learn More

IGNITE does not sell protective cases; however, if you want one, we recommend purchasing the case and antenna cable on your own and creating it at home. Links to the products needed and instructions are below.

Only three items are needed to make your own protective case:

• Armored Case External Antenna Cable
• Armored case, such as the Pelican 1050 micro case
• 1/4" drill bit

Use the 1/4" drill bit to drill a hole anywhere on the case (we recommend utilizing the top left corner, but you can place this anywhere the cable reaches.) After drilling a hole, install the Armored Case External Antenna Cable in the hole. Be sure to use both the lock washer and locknut. After the cable is installed, please attach it to your i18 and place it inside the case. You are done!

×

ANTENNA EXTENSION CABLE

6 ft. (2M) antenna extension cable for the IGNITE modules. This extension cable is used to raise the antenna up higher to improve any challenging signal situations.

ANTENNA

Replacement antenna for IGNITE modules.

IGNITE 7.4V LIPO BATTERY

Replacement 7.4V 400mAh LiPo battery.

BATTERY COMPARTMENT DOOR

Replacement battery compartment door for IGNITE modules.

EMERGENCY 9V BACKUP HARNESS

Emergency 9V Backup Harness for the IGNITE modules.

When using the Emergency 9V Backup Harness, please keep the following in mind:

• Use the 9V battery as a backup for emergencies only when your LiPo battery is fully drained.
• The 9V battery won't fit in the LiPo battery compartment, so the door won't close properly.
• For optimal results, use new Energizer or Duracell 9V batteries.
• The 9V battery isn't "more powerful" than a LiPo battery. The module fires based on current, not voltage, so even though the LiPo battery is 7.4V and the 9V battery is 9V, the LiPo battery is the appropriate choice when available.

Learn More

USB CHARGING CABLE

Cable used to charge the battery inside an IGNITE module.

IGNITE DECAL

3.9″ x 4″ die cut IGNITE decal.

PURPLE IGNITE SHIRT

A short-sleeved, 100% cotton, purple IGNITE T-Shirt, white text.